About Helix 3.5 update
Free Line 6 Helix 3.50 Firmware Update Features Entirely New IR-Based Speaker Cabinet EngineCALABASAS, CA. November 3, 2022 — Line 6 has released the free Helix® 3.50 firmware for its Helix Floor, Helix LT, Helix Rack, HX Effects™, HX Stomp™, and HX Stomp XL processors, as well as the Helix Native plugin.“The 3.50 update introduces the biggest sonic improvement to Helix since it first shipped back in 2015,” enthused Eric Klein, Chief Product Design Architect, Line 6. “There’s an entirely new IR-based speaker cabinet engine that includes 20 guitar cabs and four bass cabs with a choice of 12 microphones, and you can change their angle, position, and distance in relation to the cabs. You can even drag the mics around in space when using the HX® Edit 3.50 application. There are also five new amp models, seven new effects, a Dual IR block, and other improvements. The 3.50 update continues our unwavering support for our community of Helix and HX users.”New Speaker CabsThe 20 new guitar cabinets include a 1×10, three 1×12, five 2×12, a 4×10, and ten 4×12 models. The four new bass cabinets include 1×15, 2×15, 4×10, and 8×10 models.Despite their increased power the new cab models only utilize roughly one-third to one-fifth of the DSP as the cabs in version 3.15 and earlier due to the improved Helix Core.New Amps(Helix Floor, Helix Rack, Helix LT, Helix Native, HX Stomp, HX Stomp XL)MOO)))N T Nrm – based on* the Normal channel of the Sunn® Model TMOO)))N T
Key features of the Helix 3.5 update that are enabled through these drivers include:
- Helix Stopped Connecting to USB after update to 3.5 - Line 6
- HELIX 3.5 BACK UP PRE-update trouble - Line 6
- Late to the party but how about that 3.5 update? - Helix - Line 6
- 3.5 is here!!. That's right. It's not 3.2 it's 3.5 - Helix - Line 6
- 3.5 is here!!. That's right. It's not 3.2 it's 3.5 - Page 2 - Helix
- Helixe Native 3.5 crashes Reaper - Helix Native - Line 6
- Helix 3.5 Firmware and using a Powercab 212 - Helix - Line 6
BORE Tool holders for cutting internal threads/grooves. These holders improve on the basic internal tool holders by adding an integrated coolant bore. The coolant fluid helps to evacuate the chips, which helps to maximize tool performance, as well as extend the life of the insert.Features:Left-hand and right-hand variants availableMost tool holders are made with a 1.5° helix angle. For other angles, please consult the helix angle chart. INTERNAL HOLDERS WITH TOP CLAMP Internal tool holders for turning inserts. These holders have an additional clamp for extra insert fastening security.Features:Left-hand and right-hand variants availableMost tool holders are made with a 1.5° helix angle. For other angles, please consult the helix angle chart.Notes:Two clamping methods can be used: Screw / Top ClampFor DIR 0025 R22 and DIR 1000 R22, use the K21 torx key for C22 clamp HOLDERS WITH 3.5° HELIX ANGLE Tool holders for internal turning jobs. Unlike the standard holders that use a 1.5° helix angle, the tool holders that belong to the current product line use 3.5°.Typically, one would consider using such a tool holder in case of a large-pitch thread with a relatively small diameter. HOLDERS FOR SPECIAL APPLICATIONS The tool holders in this line of products are all optimized for one specific thread. Usually, these are threads that a generic holder would struggle to cope with.Features:Left-hand and right-hand variants available (except for SIR 0009 K08 and SIR 0354 K08)Supported Threads:1/2-13 UNCTR18x4TR20x4TR22x5TR40x7 CARBIDE SHANK BARS These carbide shank bars can be used to cut internal threads/grooves. They are especially well-suited for deep small bores with a long overhang, or for use in other situations, where chatter and deflection are expected. These bars have an integrated coolant bore, which helps with chip evacuation. This helps to maximize tool performance, as well as extend the life of the insert.Features:Left-hand and right-hand variants available INTERNAL VERTICAL HOLDERS Tool holders for internal, vertical style thread turning jobs.Features:Left-hand and right-hand variants availableNotes:These tool holders can only be used with vertical thread turning inserts – either partial profile, or full profile. STAR ⌀22MM HOLDERS A line of holders designed for use with a popular range of Swiss-type automatic lathes by Star® Micronics.Features:Supports machines with a 22mm machining diameterLeft-hand and right-hand variants available QUICK CHANGE - EXTERNAL HOLDERS The polygon shank tool holders of the Quick Change line are designed to be compliant with the ISO 26623-1 standard for toolholding systems. As such, they can be used with any coupling system that is based on the ISO 26623-1 standard, enabling quick & easy tool changes.Features:The tool holders are interchangeable with solutions by other (leading) manufacturersCooling through an internal bore is supported. This helps to evacuate the chips – aiding to maximize tool performance, as well as extend the life of the insert.A polygon taper ensures automatic radial centering, and even pressure distribution around the couplingLeft-hand and right-hand variants availableBased on a 1.4° tapered polygon shank design QUICK CHANGE - INTERNAL HOLDERS The polygon shank tool holders of the Quick Change line are designed to be
